Playground with poured-in-place safety surfacing: red path, sand and blue areas

Technical article

EPDM Playground Surfacing: Technical Guide and Thicknesses

Poured-in-place EPDM safety surfacing: two-layer system, thickness by fall height, installation, points to watch, maintenance and colour renovation.

EPDM has been the benchmark surface for playgrounds for more than twenty years. Poured in place, it forms a seamless, colourful, impact-absorbing surface that follows the shape of the ground and the footings of play equipment. This guide explains how an EPDM safety surface works, and how to size it, install it and maintain it over time. To compare it with other systems, see our page on playground safety surfacing.

What is EPDM safety surfacing?

EPDM (ethylene propylene diene monomer) is a synthetic rubber coloured throughout. Ground into fine granules and bound with a polyurethane binder, it forms the coloured top layer of playground, schoolyard and multi-sport surfaces.

An EPDM playground surface is almost always a two-layer system:

  • An impact-absorbing base layer of coarser granules, whose thickness depends on the fall height to be covered. It provides most of the impact attenuation.
  • An EPDM top layer of 10 to 15 mm, which provides the colour, patterns, comfort underfoot and wear resistance.

What thickness for what fall height?

The total thickness is sized according to the free height of fall of the tallest piece of equipment, in line with EN 1177: at that height, the surface must stay below an HIC of 1,000 and a gmax of 200 g. The higher the fall, the thicker the base layer; the top layer stays at 10 or 15 mm.

Values depend on the type of base layer, the binder ratio and the substrate. For a project, ask for the test report for the complete system proposed, and plan an on-site acceptance test. For comparison, our Calzado article gives a full thickness / fall height table, from 0.80 m to 3.00 m.

How much material for an EPDM top layer?

A 10 mm EPDM top layer uses around 10 kg of granules per m², bound with a polyurethane binder. There are two families of binder:

  • Aromatic binder: the most common and most economical, suited to strong colours. It tends to yellow under UV, which shows on light colours.
  • Aliphatic binder: non-yellowing. It is the choice for light and bright colours, and for projects where colour retention is a priority.

Installation steps

  • The substrate: concrete, asphalt or compacted sub-base, level, load-bearing and drained. A poured surface cannot be laid on soil or grass.
  • A primer suited to the substrate.
  • The impact-absorbing base layer, mixed, poured and screeded to the calculated thickness.
  • The EPDM top layer, mixed with the binder then trowelled smooth. Patterns are laid zone by zone, one colour at a time.
  • Curing before the surface is opened to use, depending on temperature and humidity.

Colours, patterns and markings

EPDM offers a wide range of colours, which can be blended to create speckled shades. A poured surface allows free-form designs: hopscotch, paths, pictograms, logos and cut-outs around equipment. To go further, 3D EPDM modules (spheres, half-spheres, animals) can be built into the surface.

Points to watch

  • Localised wear. Most of the abrasion is concentrated on a few square metres: slide run-outs, under swings, zip-line landings. These areas can be reinforced at design stage.
  • Colour retention. Under UV, EPDM can lose its brightness over the years: fading, loss of sheen or simple soiling, which are not treated in the same way.
  • Drainage. A poured surface is permeable: the water passing through it must be able to drain away through the substrate.

Maintaining an EPDM surface

  • Regularly blow or sweep away leaves, sand and debris, which clog the pores.
  • Clean with water, avoiding close-range high-pressure washing, which would tear out granules.
  • Remove moss in shaded, damp areas.
  • Visually check impact areas and have any damaged area repaired locally before it spreads. For small repairs, see our safety surfacing repair kits.

Terraludis can supply maintenance products suited to poured surfaces: contact us with a description of your surface and its condition.

Restoring the colours of an EPDM surface

A surface that is still sound but has faded can regain its colours without being replaced. Tinted aliphatic resins, applied in a thin coat on a clean, dry surface, revive or change the colour and protect the surface from UV, without yellowing. This renovation is cosmetic: it does not replace work on the base layer if impact attenuation is no longer sufficient.

For available colours and quantities for your surface, contact us with a few photos.

EPDM, Calzado or cork?

  • EPDM: the long-established standard, wide colour range, many trained installers.
  • Calzado: a circular granulate made from shoe-sole offcuts, around 6 kg/m² in the top layer instead of 10, 15 colours. See our Calzado article.
  • Natural cork: bio-based, with a natural look and no pigment. See our article on cork safety surfacing.

All three are compared on our playground safety surfacing page.

EPDM safety surfacing: frequently asked questions

What thickness for an EPDM playground surface?

The EPDM top layer is 10 to 15 mm thick; the total thickness depends on the base layer, sized for the fall height of the tallest equipment. It is justified by the EN 1177 test report for the proposed system.

Can an EPDM surface be recoloured?

Yes, with a tinted aliphatic resin designed for poured surfaces, on a sound, clean and dry surface. It revives or changes the colour and protects against UV, but does not restore impact attenuation. Contact us for available colours.

Can a hole in an EPDM surface be repaired?

Yes, with a local repair: the damaged area is cut out, the base layer rebuilt if needed, then the top layer is re-poured in the same colour. The repair is slightly visible at first, then blends in over time. Our repair kits contain everything needed for 0.5 m², in 15 colours.

Can EPDM be laid over an existing safety surface?

Depending on the condition of the existing surface, an overlay is sometimes possible. The substrate needs assessing first: send us photos of the site.

Planning an EPDM surface?

Terraludis supplies installers with materials, binders and the installation protocol. For projects outside France, we provide remote technical support by phone and video call, and installation is carried out by your local contractor. In France, we can also put local authorities in touch with a partner installer in their area. Request a technical review or a quote · Technical data sheets

Planning a surfacing project?
We support public authorities, specifiers and contractors in designing surfacing systems that meet the relevant standards and technical requirements.
Request a technical study