
Project designers, design consultancies, public authorities
Fall heights, thicknesses, quantities, specification clauses and supporting documents: we help you define the right surfacing system from the design stage.
Project completed by one of our installer customers.
Move the slider: the matching Calzado surface thickness is shown, together with the build-up and material quantities for your estimate.
Pour aller plus loin, composez votre sol dans le configurateur : couleurs, quantités et texte de CCTP à imprimer.
Three poured-in-place top layers, three different approaches. We help you choose according to the project, with no brand bias.
Circular elastomer granulate made from shoe-sole production offcuts, with multiple encapsulation in the top layer.
From 0.80 m to 3.00 m depending on thickness, backed by HIC tests.
Tested circular material, less material to install, top layer laid around 50% faster than EPDM, 15 colours.
Colour resistance to abrasion is lower than EPDM in high-wear areas (slide run-outs, under swings).
Synthetic EPDM rubber granules, coloured throughout, laid as a top layer over an impact-absorbing base layer.
Depends on base-layer thickness, verified by HIC testing.
Excellent colour resistance to abrasion, wide choice of colours, a solution installers know well.
Virgin material, slower top-layer installation and a higher material budget.
Bio-based cork granules: 3–7 mm in the base layer and 1–3 mm in a 15 mm top layer, bound with polyurethane binder.
Depends on thickness, verified by HIC testing.
Bio-based material, natural look, well suited to landscaping projects.
A thicker top layer is required (15 mm); standard polyurethane binder only.
Pour un projet biosourcé (cour d'école végétalisée, crèche, parc), voir le guide du sol amortissant en liège : épaisseurs, hauteurs de chute testées et quantités.
From first sketch to handover, a technical point of contact at your side, without taking over anyone’s responsibilities.
We start from your brief: equipment, fall heights, expected footfall and the type of existing base.
Base layer, top layer and binder defined together, with variants suited to the base, the intended use and the budget.
Quantities, typical cross-sections, technical data sheets and a specification clause for your tender documents.
Remote support (phone, video call) during the tender and liaison with the installation contractor; an on-site impact attenuation test to EN 1177 is recommended at handover.
Brochure, product data sheets, analyses and warranties, ready to attach to your tender documents.
Calzado is a circular alternative to conventional impact-absorbing surfaces, with supporting documents you can use in your award criteria.

Project completed by one of our installer customers.
A neutral starting point, with no brand imposed, to adapt to your project. Values in square brackets are to be completed.
Clause [no.] — Poured-in-place impact-absorbing surfacing for playgrounds
Supply and installation of a two-layer, poured-in-place impact-absorbing surface complying with EN 1176 and EN 1177, designed for a critical fall height of at least [free fall height of the highest piece of equipment] m.
Impact-absorbing base layer of 3–7 mm elastomer granules bound with polyurethane binder, with a thickness determined by the fall height; 10 mm top layer of 1–3 mm elastomer granules with multiple encapsulation, colour [to be specified].
The granules shall be made from pre-consumer circular material (industrial production offcuts, excluding end-of-life tyres). The contractor shall provide batch traceability and an independent laboratory test report covering, in particular, the PAH content.
The contractor shall supply the technical data sheets for the granules, binders and primer, together with the installation protocol. Acceptance shall include an on-site impact attenuation test to EN 1177. Any technically equivalent solution will be accepted on submission of supporting evidence.
Calzado brochure, data sheets and analyses, ready to append to a technical submission or a technical specification.
Working on an outdoor surfacing project, at design stage or already specified?
Let’s talk about your project