Repair kits · poured-in-place impact-absorbing surfacing

Wetpour repair kit for playground safety surfacing

Holes, torn patches, open seams: repair a poured-in-place EPDM or Calzado surface locally, without resurfacing the whole playground. Everything comes ready in the bucket: granules in your surface colour, binder, primer and tools.

0.5 m²repaired per kit
11kit colours
24 hbefore reopening
1 bucketmix right inside it
Repair kit for shock-absorbing flooring: bucket of granule mix, PU binder, primer, and spatula

Which kit for which repair?

A poured-in-place safety surface always wears in the same places: slide run-outs, under swings, along edges and around equipment posts. A small repair done early stops a hole from spreading and leaving an area with no impact absorption.

Hole, torn patch or open seam, up to 10 mm deep

Repair kit TL-KIT-R05, colour of your choice

Surface in Bright red, Pink, Sky blue or Mid grey (aliphatic-binder colours)

Contact us

Hole deeper than 10 mm: the base layer is damaged

TL-KIT-SC05 base-layer top-up + R05 kit

Damaged area larger than 0.5 m²

1 kit per 0.5 m²

Large area or surface needing full replacement

Contact us: we supply the system and installation protocol to your installer, with remote technical support

Two products to repair a poured-in-place surface

The granules come in a 16 L bucket that doubles as the mixing tub: pour the binder over the granules and mix directly in the bucket. No extra tub, no weighing on site.

Calzado repair kit for shock-absorbing flooring: bucket of red granules, PU binder, and primer

TL-KIT-R05

Calzado repair kit

10 mm top layer, aromatic polyurethane binder (summer or winter formula depending on the season). Available in 11 of the 15 Calzado colours.

  • 4 kg of 1–3 mm top-layer granules, colour of your choice
  • 0.8 kg of aromatic PU binder
  • 0.25 kg of bonding primer
  • 16 L bucket, spatula, brush, gloves, instructions
Technical data sheet (PDF)
Underlayment repair kit for shock-absorbing flooring: bucket of 3-7 mm granules and PU binder

TL-KIT-SC05

Base-layer top-up

For deep holes: rebuild the base layer, levelled 10 mm below finished level without compacting, then apply the top layer from an R05 kit.

  • 4 kg of 3–7 mm Calzado base granules, 100% shoe-sole offcuts
  • 0.5 kg of base-layer PU binder
  • 0.5 m² at 20 mm or 1 m² at 10 mm
  • 16 L bucket, instructions
Technical data sheet (PDF)

6 kg/m²

of granules for 10 mm, compared with about 10 kg/m² for an EPDM top layer

8 h

before walking on the repaired area

24 h

before reopening the playground

6 months

shelf life, unopened, protected from frost

Repairing a playground surface in 8 steps

Installation instructions are supplied with every kit. In outline:

  1. 1. Mark out

    Draw a simple shape around the damaged area, overlapping slightly onto the sound surface.

  2. 2. Cut out

    Cut with a utility knife, keeping the edges straight and vertical, down to a sound base.

  3. 3. Clean

    Vacuum up dust and debris: the bottom and edges must be clean and dry.

  4. 4. Rebuild

    If the hole is deeper than 10 mm: mix the base-layer top-up in its bucket, spread it and level it 10 mm below finished level, without compacting. Leave to dry for 8 h.

  5. 5. Prime

    Brush primer onto the bottom and edges in two coats.

  6. 6. Mix in the bucket

    Pour the binder over the granules and mix until they are fully coated, with no dry lumps.

  7. 7. Apply

    Spread in one go and smooth with the spatula flush with the existing surface, taking care over the edges.

  8. 8. Leave to cure

    Cordon off the area: 8 h before walking on it, 24 h before reopening the playground.

The base must be clean, dry and sound; a new concrete screed needs three weeks to dry. Below 6 °C the binder does not cure properly: postpone the repair. Rain affects curing: check the forecast for the hours after installation, not just for the day. On an older surface, the repaired area may look brighter for the first few months until it weathers.

11 kit colours to match your existing surface

The kit top-layer granules come in 11 of the 15 Calzado colours. Tell us the colour of the surface to be repaired, or send a photo, and we will suggest the closest shade. Bright red, Pink, Sky blue and Mid grey require an aliphatic binder: there is no kit for these colours, please contact us.

PCE03 · Beige

PCE04 · Ochre

PCE05 · Yellow

PCE06 · Orange

PCE07 · Red

PCE08 · Bright red · contact us

PCE09 · Pink · contact us

PCE10 · Dark blue

PCE11 · Sky blue · contact us

PCE12 · Bright green

PCE13 · May green

PCE14 · Pine green

PCE15 · Brown

PCE16 · Mid grey · contact us

PCE17 · Anthracite

Closest RAL shades; on-screen colours are indicative only.

Frequently asked questions about playground surface repair

Can an EPDM surface be repaired with a Calzado kit?

Yes. The kits are designed for holes, torn patches and open seams in poured-in-place surfaces, whether Calzado or EPDM. Simply choose the colour closest to the existing surface.

What area does one kit repair?

One kit repairs 0.5 m² of top layer at 10 mm thick. For larger areas, allow one kit per 0.5 m². For a large area or a surface that needs replacing entirely, a repair by an installer is more appropriate.

What if the hole is deeper than 10 mm?

This happens with a deep tear or a hollow under a swing: the base layer is damaged. Rebuild it with the TL-KIT-SC05 top-up (0.5 m² at 20 mm or 1 m² at 10 mm), then apply the top layer from an R05 kit.

What about a Bright red, Pink, Sky blue or Mid grey surface?

These four colours require an aliphatic binder, which does not yellow in sunlight. There is no kit for them: contact us with a photo of the surface and we will work out the repair with you.

When can the playground reopen?

The surface is dry after 8 h and can be walked on. Full curing takes 24 h, after which the playground can reopen to children.

Will the repair be visible?

On an older surface, the repaired area may look brighter for the first few months until it weathers. To refresh the colour of a whole surface, tinted aliphatic binders are available: contact us.

Who can use the kits?

The kits are for professional use only: technical services, playground operators and installation contractors. The binder contains diisocyanates: gloves are supplied, work must be done outdoors, and adequate training is required for professional use. The safety data sheet is included.

How long does a kit keep?

Six months, unopened, protected from frost and moisture. An opened container will not keep: prepare the mix at the time of the repair.

How do I order?

Tell us the area to be repaired, the depth of the holes and the colour of the surface, ideally with photos. We will confirm which kits you need, the price and the lead time. Request a quote.

Further reading: our EPDM safety surfacing guide, Calzado, the EN 1177 standard and our playground safety surfacing.

Kit technical data sheets

Download the technical data sheets. Prices, lead times and the safety data sheet are available on request.

Got a surface to repair?

Send us two or three photos of the damaged area, its size and the colour of the surface: we will tell you which kit and how many to order.

Send my photos